M O T O R I Z E D    F L O W    C O N T R O L

The Source Motorized Flow Control provides economical and simple electric remote control for flows up to 50 GPM. It uses a 12 volt DC motor to open or close a rotary spool valve. The flow rate is changed by providing a 12 volt signal to either increase or decrease valve opening. In its simplest form, the control element is a DPDT three position-momentary-contact toggle or rocker switch or two DP momentary-contact push buttons.

If a more sophisticated control is desired, the loop can be closed by using a control amplifier and relay circuit in conjunction with feedback from a flow or speed sensor.

The valve requires no power to maintain its flow setting. A 12 volt DC signal is applied only while changing the flow rate and then shut off to hold flow rate at the desired setting. In the event of a power failure or system shut down, the valve will remain at its current flow setting until power is restored and a command signal is once again applied. Valve design allows for manual over-ride in case of electrical failure.

The valve is internally protected and will automatically shut down the internal drive when either the full open or full closed positions are reached.

F E A T U R E S

• Internally protected  • Requires no power to maintain setting  • Safe  • Flexible  • Efficient  • Simple to use  • Economical


S P E C I F I C A T I O N S

DESCRIPTION
  • MFC-10 and MFC-16 valves are cartridge design and will fit generic 10-2 and 16-2 cavities respectively.

    • OPERATING PRESSURE

  • 3000 psi (5000 psi with factory approval)

    • FLOW RATING
    (Based on 100 psi with valve fully open)

  • 0-5 GPM MFC-10-5-12V-**
  • 0-15 GPM MFC-10-15-12V-**
  • 0-20 GPM MFC-16-20-12V-**
  • 0-35 GPM MFC-16-35-12V-**
  • 0-50 GPM MFC-16-50-12V-**

    • CONSTRUCTION

  • Nose, body and spool: steel
  • Exposed parts plated
  • Motor container assembly: anodized aluminum
    		•  
    OPERATING SPEED
    (Fully closed to fully open @ 12V DC)
  • 3.5 seconds (-03 option)
  • 7 seconds (-07 option)
  • 24 seconds (-24 option)
  • 48 seconds (-48 option)

    • VOLTAGE

  • 12V DC
  • For 24V DC operation, add 100-ohm resistor in series with motor

    • CURRENT DRAW

  • Less than 120 MA typical @ 12V DC

    • CARTRIDGE WEIGHT

  • MFC-10: 1.3 lb.
  • MFC-16: 1.6 lb.


    • T Y P I C A L   C I R C U I T   A P P L I C A T I O N S
    Note: the following links are PDF documents which require viewing software fromwww.adobe.com
    • Circuit 1
      F10 - 0 to 15 gpm motorized flow control in load sense body
      F16 - 0 to 50 gpm motorized flow control in load sense body

    • Circuit 2
      F10/25206 - 0 to 15 gpm motorized flow control in 2-port pressure compensated body
      F16/25206 - 0 to 50 gpm motorized flow control in 2-port pressure compensated body
      SFP25275 - Bankable 2-port pressure compensated flow control sections with load sense

    • Circuit 3
      F10/25201 - 0 to 15 gpm motorized flow control in 3-port pressure compensated body
      F16/25201 - 0 to 50 gpm motorized flow control in 3-port pressure compensated body

    • Circuit 4
      F10/25201-R - 0 to 15 gpm motorized flow control in 3-port PC body with system relief
      F16/25201-R - 0 to 50 gpm motorized flow control in 3-port PC body with system relief

    • Circuit 5
      F10/25201-R-S - 0 to 15 gpm MFC in 3-port PC body with system relief and on-off solenoid
      F16/25201-R-S - 0 to 50 gpm MFC in 3-port PC body with system relief and on-off solenoid

    back   Return to Source Fluid Power Products page